JDY-40 2.4GHz Kablosuz Seri Alıcı Verici Transceiver Modülü
120 Metre Serial Port Rf Uzaktan İletişim Haberleşme TTL IO Kontrol Modülü Kapı Oyuncak Akılı Ev
JDY-40 2.4Ghz frekansında çalışan rf alıcı verici modüldür. Açık alanda 120 metre seri port iletişimi yaptırabilir. Kolayca devrelerinize entegre edebilirsiniz. 8 Adet Io pini bulunmaktadır. Bu şekilde 8 farklı cihaz kontrolü yada giriş takip edilebilir.
Özellikler:
- Model: Jdy-40
- Frekans: 2.4Ghz
- Çalışma voltajı: DC 2.2V / 3.3V
- Haberleşme mesafesi: Açık alanda 120 metre
- IO sayısı: 8
- Rf gücü: 12dB Maksimum
- Tx akımı: 40mA
- Rx akımı: 20mA
- Uyku akımı: 5uA
- Haberleşme tipi: TTL seri port
- Haberleşme hızı: 9600
- Reception sensitivity: 97dB
- Çalışma sıcaklığı: -20C / 80C
- Renk: Mavi
- Boyutlar: 14mm x 22mm
- Ağırlık: 0.5gr
Paket İçeriği :
- 1 Adet JDY-40 2.4G Wireless Serial Transceiver
Pin function description:
| Pin | The name of the discipline | Function |
| 1 | GPI01 | Input-output IO, which can be configured by AT+CLSS |
| 2 | GPI02 | Input-output IO, which can be configured by AT+CLSS |
| 3 | GPI03 | Input-output IO, which can be configured by AT+CLSS |
| 4 | GPI04 | Input-output IO, which can be configured by AT+CLSS |
| 5 | GPI05 | Input-output IO, which can be configured by AT+CLSS |
| 6 | GPI06 | Input-output IO, which can be configured by AT+CLSS |
| 7 | GPI07 | Input-output IO, which can be configured by AT+CLSS |
| 8 | GPI08 | Input-output IO, which can be configured by AT+CLSS |
| 9 | VCC | Power supply (2.2-3.6) |
| 10 | RXD | Serial port input pin |
| 11 | TXD | Serial port output pin |
| 12 | SET | AT command switching pin (low level AT instruction, high level transparent transmission) |
| 13 | CS | Transmission or push button mode: CS pin (low level wake-up, high level sleep). IO receive mode:the CS pin needs to be suspended or pulled up |
| 14 | GND | Power supply |
Default configuration:
| sequence | function | parameter | instructions |
| 1 | baud rate | 9600 | AT+BAUD |
| 2 | wireless ID | 8899 | AT+RFID8899 |
| 3 | device ID | 1122 | AT+DVID1122 |
| 4 | channel | 001 | AT+RFC001 |
| 5 | emissive power | 12db | AT+POWE9 |
| 6 | equipment type | A0 | AT+CLSSA0 |
Communication:
It is necessary to configure the RFC, DVID, and RFID that need the communication module to be the same. The module and the module can communicate. When the module comes out, the parameters are all unified, and the user can configure it according to its own needs.
AT instruction instructions:
Specifically, the JDY-40 module needs to add the ending symbol rn to send the AT instruction.
Set / query - baud rate:
| instructions | response | response |
| AT+BAUD | OK | Param(1-7) 1:1200 2:2400 3:4800 4:9600 5:14400 6:19200 Default value:4 |
| AT+BAUD | +BAUD= |
Set / query -RFID:
| instructions | response | response |
| AT+RFID | OK | Param(0000-FFFF) Default value:8899 |
| AT+RFID | +BAUD= |
Set / query -DVID:
| instructions | response | response |
| AT+DVID | OK | Param(0000-FFFF) Default value:8899 |
| AT+DVID | +BAUD= |
Set / query -RFC:
| instructions | response | response |
| AT+RFC | OK | Param(001-128) Default value:001 |
| AT+RFC | +RFC= |