- Stok Durumu: Stok Var
- Marka: OEM
- Model: ESP32-C3 Süper Mini
- SKU: RBZ.101.361
ESP32 C3 Super Mini Development Board Wifi Bluetooth Type-C Usb
160Mhz 4MB Flash 400kb PSRam MicroPython Arduino Iot ADC I2C SPI UART
No documentation is included with the product. No additional software support will be provided.
ATTENTION: Newly arrived boards come unprogrammed, therefore the BOOT button must be held pressed while plugging in the USB cable at first connection. In this case the product starts operating in programming mode.
It is a development board capable of wireless communication and compatible with arduino. The Esp32C3 chip is used in the module. It can be programmed over the Type C usb port. It receives power over the Usb port. It can operate with external 5V supply.
It has 13 digital input output pins. There are reset and boot buttons and 1 user led on the board. There are empty header slots for connection on the board edges. In addition, these pads have a design that can be soldered from the board edge onto a lower board. By creating a low height on the lower board, you can make projects that fit into very small boxes.
It can be programmed over Micropython. It can also be programmed over Arduino IDE. It is used in IOT, wireless internet control applications, various sensor reading, and similar internet based projects.
When you plug it into the pc, 1 com port and 1 jtag device appear automatically in the system. If you press the reset button while the boot button is held pressed and then release the boot button, the product enters programming mode.
Features:
- Model: ESP32 C3 Mini
- Chip ESP32C3FN4
- Operating speed: 160Mhz
- Flash: 4MB
- PSRAM: 400kb
- Rom: 384kb
- 2.4Ghz Wifi communication support (802.11 b/g/n)
- Bluetooth 5 communication support
- 13 Digital input/output io pins
- All pins have interrupt / pwm / I2C / one-wire support.
- ADC, I2C, SPI, UART, USB OTG
- Ceramic antenna on the board
- Operating voltage: DC 3.3V
- Power and communication: USB Type-C
- Comes with MicroPython software loaded.
- Can be programmed with Arduino and ESP-IDE.
- Reset button
- Boot button
- 1 Piece user led GPIO8
- Color: Purple
- Operating temperature: -10C / +65C
- 2 pieces of 2x8 empty connection socket on 2 edges.
- Dimensions:18mm x 23mm
- Weight: 2gr
Software support:
- microsoft.github.io/devicescript/devices/esp32/esp32c3-supermini
- You can add the Esp32 package to the Arduino IDE from the board manager with the link below.
https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json
- In Arduino, the “USB Cdc on boot” enable selection may need to be made.
- thonny.org has microphyton support.
- waveshare.com/wiki/ESP32-C3-Zero
- espressif.github.io/esp32-c3-book-en/
Package contents:
- 1 Piece ESP32-C3 Super Mini
- 2 Pieces 8 Pin Male Header
| Feature | ESP32-C3 SuperMini | ESP32-S3 SuperMini | ESP32-C6 SuperMini | ESP32-H2 SuperMini |
|---|---|---|---|---|
| CPU | 32-bit RISC-V, single-core @160MHz | Dual-core Xtensa LX7 @240MHz | 32-bit RISC-V, single-core @160MHz | 32-bit RISC-V, single-core @96MHz |
| Wireless | WiFi 4, Bluetooth 5 (LE) | WiFi 4, Bluetooth 5 (LE) | WiFi 6 (802.11ax), BLE, BLE Mesh | Thread, Zigbee (IEEE 802.15.4), BLE |
| Antenna | PCB antenna | PCB antenna | PCB antenna | PCB antenna |
| Flash / RAM | 4MB / 400 KB SRAM | 4MB / 512 KB SRAM | 4MB / 512 KB + 16 KB LP SRAM | 4MB / 320 KB SRAM + 4 KB LP SRAM |
| Form Factor | 22.52 x 18 mm | ~1 pin row longer | ~2 pin rows longer | ~1 pin row longer |
| Onboard LED | Blue LED (GPIO8) | WS2812 RGB | RGB LED (GPIO8) | Standard LED (GPIO13) |
| USB Interface | USB Type-C | USB Type-C | USB Type-C | USB Type-C |
| Battery Charging Support | ❌ None | ✅ BAT+ / BAT- pins | ✅ BAT+ / BAT- pins | ✅ BAT+ / BAT- pins |
| Special Features | Minimal form, stable PCB antenna | Dual-core, RGB LED, more GPIOs | WiFi 6, BLE Mesh, Zigbee/Thread, USB-C, RGB LED | Thread/Zigbee, BLE, USB-C |
| Power Consumption (Deep Sleep) | ~43μA | ~43μA | Ultra-low power modes | Ultra-low power modes |
